There is a “normal” load that an engine can handle. \u00a0If you load the engine more, it will turn slower, run hot, use more fuel, and deliver less power. \u00a0On the other hand, inadequate loading will not allow the engine power to be transformed into thrust. \u00a0Possibly the most well known normal propeller is the 10×6 for a 40 size engine.<\/p>\n
Propeller Rule #2<\/strong><\/p>\n You can increase the pitch of the propeller if you decrease diameter, or vice versa, while maintaining the same loading on the engine. \u00a0This is kind of like shifting gears in a car. \u00a0So in addition to the normal 10×6 your standard 40 engine can use a 9×7, or 11×5, as well as other sizes. \u00a0Greater pitch makes the plane go faster at the expense of acceleration. \u00a0Less pitch will produce better acceleration, at the expense of top speed.<\/p>\n Other factors that affect Rule #1 and #2<\/strong><\/p>\n Most propeller related confusion arises from the fact that the propeller rules are subject to a higher rule about the drag of your airplane. \u00a0So let’s go back to the standard 40 size plane again. \u00a0Consider an average sport plane such as the Super Sportster.<\/p>\n It has\u00a0an average amount of drag for its size and can fly\u00a0at an average speed. \u00a0With an average 40 size engine you can use an average 10×6 prop and be happy. \u00a0But you won’t win a pylon race\u00a0with a 6 pitch because the prop will go only as far as it’s going to go, according to the pitch of the blade. \u00a0So the guy with a 9×7\u00a0prop will win the race with the same engine. \u00a0This seems simple enough, but the propeller rules are subordinate to the drag of the airframe. \u00a0Once the drag\u00a0equals the total power of the engine it doesn’t matter what prop you put on. \u00a0The plane just won’t go any faster. \u00a0You may have heard of a propeller “unloading” in the air. \u00a0This is where the airspeed is\u00a0close enough to the theoretical pitch speed that the engine doesn’t have to work\u00a0so hard to get the air through the prop. \u00a0Excessive airframe drag causes the engine to keep lugging because it\u00a0doesn’t have enough power to get it close to pitch speed. \u00a0So, going back to the pylon race I mentioned earlier, the guy with the 9×7 prop will win\u00a0only if\u00a0the airplanes are not already operating at their drag-induced speed limit. \u00a0If they are, then the 9×7 guy\u00a0needs to reduce drag before his high pitch propeller will do him any good. \u00a0Or, failing that, he will need to use a more powerful engine.<\/p>\n The same principle applies to slow and draggy planes as well. \u00a0You can fly a really big old-timer with a 40 size engine.<\/p>\n Photo I found on the internet. Thanks to whoever posted it.<\/p><\/div>\n These planes are very light and they have a lot of drag, so they fly best at low speeds. \u00a0With the appropriate engine, drag will prevent them from going fast, so\u00a0if you use a high pitch prop it will never be able to unload and will therefore run hotter and use more fuel. \u00a0In these cases you may want to try 11×5 or 12×4, or even a 12×3 if you can get it. \u00a0These low pitch props will yield strong climb and acceleration at the expense of speed, but your plane can’t go fast anyway, so no problem. \u00a0But there is a limit. \u00a0At the slow\u00a0end of the spectrum the hard limit is your stall speed. \u00a0You can go only so far before the plane just won’t fly because your low pitch prop isn’t generating\u00a0enough airspeed.<\/p>\n You get a bit of a break because of the exponential nature of aerodynamic drag. \u00a0Total parasite\u00a0drag is a function of the square of the airspeed, multiplied by a factor determined by the shape of the airplane (the amount of drag it causes). You can equip your fast plane with a high pitch prop for speed without worrying\u00a0about acceleration because such planes usually have a slick airframe so as to reduce drag, making it easier for your plane to accelerate in spite of the high pitch prop. Likewise,\u00a0you prop your lightweight draggy old timer or biplane for acceleration, because it has too much drag for the engine to overcome to make it go fast, and it doesn’t need to go fast anyway.<\/p>\n Solving your real-world problems:<\/strong><\/p>\n RC flying presents a lot of mysteries to the uninitiated. \u00a0If your engine keeps overheating and dying in the air, most folks would assume that your needle is too lean. \u00a0The obvious explanation is that you are stupid or the engine is a piece of junk or your fuel went bad, because try as you might, you just can’t find the optimal needle setting. \u00a0But maybe you just have too much pitch on your propeller, the airplane is at its drag limit for the available power, and the engine can’t get the plane fast enough to unload the prop. \u00a0The inability to unload causes the engine to overheat, which requires a rich needle, which uses more fuel and causes a loss of power and unreliable running. \u00a0I’ve seen a lot of guys in this situation cursing the engine, trying different fuel, replacing glow plugs, etc. \u00a0Another common theory is that a 40 plane flies better with a 60, and that always solves the problem (and increases weight, turning radius, fuel consumption, etc). \u00a0If you are in fact suffering from excessive pitch, a propeller swap just might solve all of these problems. \u00a0Even if it isn’t a panacea it usually helps at least a little bit.<\/p>\n So here is the complete integrated set of rules:<\/p>\n #1 Always stay in the load range for your engine, starting with the “normal” prop and increasing one number while decreasing the other.<\/p>\n #2 Increase pitch for higher speed, until you reach the hard limit imposed by drag vs. power. \u00a0Overpitching beyond this point will overload your engine because of inability to unload in the air. \u00a0Decrease pitch for better acceleration, if you don’t need high speed performance anyway, but stop when you reach the limit where the plane doesn’t have enough head room above stall speed.<\/p>\n","protected":false},"excerpt":{"rendered":" I don’t have much to say about electric flight, so if you want to learn about propeller selection for your electric powered plane you’ll probably have to ask somebody else. \u00a0But I can offer some help for those who want … Continue reading ![\"gpma0205-1b\"](\"http:\/\/www.balsaworkbench.com\/wp-content\/uploads\/2017\/06\/gpma0205-1b.jpg\")
<\/a><\/p>\n<\/a>